It is inevitable that there will be some small mistakes in the welding process of the automatic welding equipment for girth seam, so how to prevent them? Today, the price of Shandong automatic welding equipment for circumferential seam is introduced to you as follows:

1、氣孔。在全位置焊中應用自動焊接設備時，氣孔是一種比較常見的問題，導致該問題產生的原因有很多，比如焊材自身的原因、操作不當、環境原因等。

1. Stomata. When automatic welding equipment is used in all position welding, air hole is a common problem, which is caused by many reasons, such as welding material itself, improper operation, environmental reasons, etc.

鑒于此，為有效地防止這一問題，在實施焊接時，應加強氣體的保護，焊接溫度不可過高，嚴格按照比例以及相關要求來充裝氣體，確保充裝純度達到要求。同時還要注意施焊場地周?chē)沫h(huán)境，若施工場地的風速每秒超過8米，應用防風棚來實施防護，且環境濕度不可過大。此外，為確保施焊位置保持干燥，可利用環形火焰加熱器或中頻感應加熱器來實施加熱。

In view of this, in order to effectively prevent this problem, in the implementation of welding, the gas protection should be strengthened, the welding temperature should not be too high, and the gas should be filled in strict accordance with the proportion and relevant requirements to ensure that the filling purity meets the requirements. At the same time, we should also pay attention to the environment around the welding site. If the wind speed of the construction site exceeds 8 meters per second, the wind shed should be used for protection, and the environmental humidity should not be too high. In addition, in order to keep the welding position dry, ring flame heater or medium frequency induction heater can be used for heating.

2、未熔合。環縫自動焊接設備在焊接過程中，未熔合這一問題一般常出現于立焊位置，導致該問題的原因有焊道打磨形狀不正確、在焊接時偏離焊縫或者焊槍擺動的寬度不夠合理等。鑒于此，在焊接過程中，在實施焊道打磨作業時，應盡量打磨平整。

2. No fusion. In the welding process of automatic girth welding equipment, the problem of non fusion often occurs in the vertical welding position. The causes of the problem include incorrect grinding shape of weld bead, deviation from the weld during welding or unreasonable swing width of welding gun. In view of this, in the welding process, in the implementation of bead grinding operation, should try to smooth grinding.

同時在焊接之前，還應對焊絲進行仔細地觀察，察看其擺動寬度是否正確。此外，在焊接過程中，如發現焊接熔池和焊道中間出現偏離，應及時實施調整，以免出現未熔合問題。

At the same time, before welding, the welding wire should be carefully observed to see if its swing width is correct. In addition, in the welding process, if there is deviation between the weld pool and the weld bead, it should be adjusted in time to avoid non fusion.

以上就是小編為大家介紹的如何防止環縫自動焊接設備的焊接失誤，希望為大家帶來幫助！

The above is a small series for you to introduce how to prevent the welding error of automatic welding equipment, hope to help you!